Drive Restorer
Windows 10 & 11 Buy license · $29.95
Drives and devices

How to Recover Data From a Failing or Clicking Hard Drive

Hard drive clicking, slow or throwing errors? Learn the warning signs, what not to do, and how to image a failing drive and recover data from the copy.

Updated 5 minute read The Drive Restorer team

To recover data from a failing hard drive, copy the most important files off first if the drive is still readable, then create a drive image (a sector-by-sector copy) on a healthy drive and run any recovery scans on the image instead of the failing disk. Do not run CHKDSK, defragment or keep rebooting from the drive. If the drive clicks, grinds, is not detected or has been dropped, stop using it and consider a professional data recovery lab, because every power-on can cause more damage.

Below are the warning signs, what to do in what order, and an honest look at where software helps and where it does not.

Signs a hard drive is failing

SymptomLikely meaningSoftware recovery?
Very slow file copies, freezes when opening foldersBad or weak sectors being retriedOften, using an image
Files that will not open or copy, CRC or I/O errorsUnreadable sectorsOften, using an image
SMART warning from Windows or the BIOSThe drive is reporting its own problemsYes, act now
Drive shows as RAW or asks to be formattedFile system damage, sometimes from bad sectorsUsually
Repeated clicking, grinding or scrapingMechanical fault: heads or motorUnlikely; see a lab
Not detected at all, or detected with the wrong sizeElectronics, firmware or mechanical faultNo; see a lab
Beeping, or spins up and stopsOften stuck heads or motor problemsNo; see a lab

For a quick health check, open PowerShell and run Get-PhysicalDisk | Select FriendlyName, HealthStatus. "Healthy" means Windows is not seeing a reported problem, but a drive can still be failing without a warning, so trust the symptoms above over a single status line. The drive maker's own diagnostic tool gives a more detailed report.

What not to do with a failing drive

  • Do not run CHKDSK. It reads and writes across the whole drive and can remove damaged file records you need for recovery.
  • Do not defragment, optimize or "repair" the drive with any tool.
  • Do not keep booting Windows from it if it is your system drive. Windows reads and writes constantly in the background.
  • Do not open the drive or try home remedies such as freezing it or tapping it. Opening a hard drive outside a cleanroom contaminates the platters.
  • Do not run repeated full scans directly on the drive. Each pass is more wear on weak heads and surfaces.

Step 1: Copy the most important files first

If the drive is still readable in File Explorer, start by copying the files you cannot live without to a healthy drive: one folder at a time, most important first. Skip anything that is not essential. A drive that is failing slowly may get worse during a long session, so prioritize.

If a copy hangs on a particular file, skip it and move on rather than retrying again and again. You can try that file later from an image.

Step 2: Image the drive

A drive image is a complete, sector-by-sector copy of the disk saved as a file on another drive. Once you have an image, all your recovery work can be done on the copy, so the failing drive is read only once.

  • Space: the destination drive needs at least as much free space as the full size of the failing drive, not just the used space, because deleted files live in the "free" space too.
  • Connection: connect the failing drive directly, internally or with a good USB 3 adapter, and use its own power supply if it has one.
  • Time: imaging a healthy 1 TB drive over USB 3 can take a few hours. A drive with bad sectors can take much longer.

Drive Restorer lets you image a failing drive and then recover from the image. Our step-by-step guide to creating a disk image of a failing hard drive covers the details.

Step 3: Recover files from the image

  1. Open the drive image in Drive Restorer as the source to scan.
  2. Run a quick scan to find existing and deleted files with their names and folders.
  3. Run a deep scan if parts of the file system are damaged. It reads the image sector by sector and finds files by their content.
  4. Filter and preview. Check important files in the preview and look at the recovery chance rating, which shows where unreadable areas have damaged a file.
  5. Restore to a healthy drive, separate from the one holding the image if possible.

Because you are scanning a copy, you can run as many scans as you like, save them and resume later, without putting the original drive at further risk.

When to go to a professional lab

Software reads a drive through its own heads and electronics. When those are what has failed, no software can help. A data recovery lab can replace parts in a cleanroom and read the platters directly. Consider a lab when:

  • the drive clicks, grinds, beeps or does not spin,
  • it is not detected in Disk Management or the BIOS,
  • it was dropped, flooded or burned,
  • or the data is irreplaceable and you are not willing to take any risk.

Our comparison of data recovery software vs a recovery service helps you decide which route fits your situation.

If a lab is a possibility, decide before you start. Each attempt to read a mechanically failing drive can turn a recoverable case into an unrecoverable one, and labs generally prefer drives that have not had repeated software attempts.

Failing system drive: getting it out of the PC

If the failing drive is the one Windows runs from, every boot reads and writes thousands of files on it. The safer route is to shut the PC down, remove the drive and connect it to another Windows PC as a second drive, using a SATA-to-USB adapter or a spare internal connection. That PC then images and scans it without starting Windows from the weak drive. In a laptop, the drive is often behind a single panel on the underside, but check the maker's service guide before opening it.

After recovery

Replace the failing drive. Even if it seems to work again after a restart, drives that have shown errors rarely recover. Copy your recovered files to the new drive, keep a second copy elsewhere, and set up a regular backup so the next failure costs you nothing but the price of a drive.

Frequently asked questions

Should I run CHKDSK on a failing drive?

No. CHKDSK reads and writes the whole drive and can make a failing drive worse. Copy your data or create a drive image first.

Can software recover data from a clicking hard drive?

Sometimes, if the drive is still detected. Clicking often means a mechanical fault, so read the drive as little as possible and consider a professional lab for important data.

Does putting a hard drive in the freezer work?

No, it is not recommended. Condensation can damage the platters and heads. A professional lab is the right choice for a drive that has failed mechanically.

Get three guides like this every month, plus software update notices.Subscribe →