Drive Restorer
Windows 10 & 11 Buy license · $29.95
Drives and devices

How to Create a Disk Image of a Failing Hard Drive Before Recovery

Why and how to create a disk image of a failing hard drive before recovery: how much space you need, where to save it and how to recover from it.

Updated 6 minute read The Drive Restorer team

To create a disk image of a failing hard drive, connect the drive to a healthy Windows PC, make sure a second drive has at least as much free space as the whole failing drive, and use imaging software to copy it sector by sector into a single image file. Then run every recovery scan on that image, never on the failing drive. Imaging reads the weak drive once, from start to end, instead of the many passes a recovery scan can make, so you get a usable copy before the drive gets worse.

This guide covers when imaging is the right call, how to prepare, how to do it and how to recover files from the image afterwards.

Why image first instead of scanning the drive

A recovery scan jumps around the disk. It reads the file system, follows records, goes back for file contents and, in a deep scan, reads every sector looking for known file types. On a healthy drive that is fine. On a drive with weak heads or a growing number of bad sectors, every extra read is wear, and some drives fail completely part way through a long session.

An image changes the order of events:

  • The failing drive is read once, in one long sequential pass, which is the gentlest way to read a hard drive.
  • Everything after that happens on the copy. You can run a quick scan, a deep scan, a partition search, stop, start again and try different filters, with no risk to the original.
  • If the drive dies the next day, you still have everything that was readable when you imaged it.

When imaging is and is not the right move

SituationImage first?
Drive is slow, freezes, or shows read errors on some filesYes
SMART warning, or the drive is getting worse day by dayYes
Drive shows as RAW but otherwise behaves normallyRecommended, especially if it is old
Healthy drive, files simply deletedNot needed; scan it directly, read-only
Drive clicks, grinds, beeps or does not spinNo. Power it down and consider a lab
Drive is not detected by Windows or the BIOSNot possible. It needs a lab

Imaging needs the drive to be visible to Windows. If Disk Management cannot see it, no imaging tool can read it either. Our guide to recovering data from a failing hard drive covers the warning signs in more detail.

What you need before you start

  • A healthy destination drive. It needs free space of at least the full capacity of the failing drive, not just the space that is used. A 1 TB drive needs a 1 TB image, because deleted files live in the space Windows calls "free".
  • The right file system on the destination. Format it as NTFS or exFAT. FAT32 cannot hold a single file larger than 4 GB, so a whole-disk image will not fit on it.
  • A stable connection. Connect the failing drive internally or with a good SATA-to-USB 3 adapter. Use a mains power supply for 3.5-inch drives. Avoid unpowered hubs and long, loose cables.
  • Time. A healthy 1 TB drive can take a few hours over USB 3. A drive with many bad sectors can take much longer. Make sure the PC will not sleep: in Settings → System → Power, set sleep to Never for the session.

Never save the image to the failing drive itself, or to another partition on the same physical disk. The image must go to a separate, healthy physical drive.

If the failing drive is your Windows drive

Do not image it while Windows is running from it. Windows reads and writes constantly in the background, which is exactly the wear you are trying to avoid, and the files keep changing while you copy them. Shut the PC down, remove the drive and connect it to another Windows 10 or 11 PC as a second drive. A USB adapter or docking station makes this easy for both 2.5-inch laptop drives and 3.5-inch desktop drives.

When you connect it, Windows may offer to scan and fix the drive or ask you to format it. Dismiss both prompts. Do not run CHKDSK on a failing drive.

How to create the image step by step

Drive Restorer can copy a failing drive to an image file and then recover from that copy. The general process looks like this:

  1. Connect both drives: the failing source and the healthy destination. Close other programs that might scan new drives, such as photo importers or backup tools.
  2. Select the source by physical disk, not just a drive letter. Imaging the whole physical disk captures every partition, the partition table and the unallocated space, which matters if a partition has gone missing.
  3. Choose the destination folder on the healthy drive, for example D:\Images\, and give the image a clear name with the drive model and date.
  4. Start the image and leave the PC alone. Do not open files on the source drive while it runs.
  5. Watch for slow areas. A run of bad sectors shows up as a slowdown. That is normal on a failing drive. If the drive starts clicking or disappears from Windows, stop and power it down.
  6. When it finishes, disconnect the failing drive and put it somewhere safe. You may still want it later, for example if you decide to send it to a lab.

Unreadable sectors cannot be copied. They are left empty in the image, and any file that sat in those sectors will be partly damaged when you recover it. Everything else is a faithful copy.

Recovering files from the image

Once the image exists, treat it like a healthy drive:

  1. Open the image file as the source to scan in Drive Restorer.
  2. Run a quick scan to read the file system and list existing and deleted files with their names and folders.
  3. Run a partition search if partitions are missing, and a deep scan if parts of the file system are damaged. The deep scan finds files by their content, though often without their original names.
  4. Filter the results by type, date, size and name to find what matters.
  5. Preview important files and check the recovery chance rating. Files that overlapped bad sectors usually show as partly damaged.
  6. Restore to a third location if you can, or at least to a separate folder from the image.

Long deep scans of large images can be saved and resumed later, so you do not have to finish in one sitting. For how the two scan types differ, see quick scan vs deep scan.

What about the Windows "system image" tool?

Windows still includes the older Backup and Restore (Windows 7) tool in Control Panel, which can create a system image. It is a backup tool, not a recovery tool. It copies the used parts of volumes rather than every sector, so deleted files in free space are not included, and it is designed for healthy drives. It usually fails when it meets bad sectors. For recovery, you want a full sector-by-sector image of the physical disk.

After recovery

  • Open a sample of the recovered files in their normal programs to confirm they work.
  • Keep the image until you are sure you have everything. Storage is cheaper than a second attempt on a dying drive.
  • Replace the failing drive. Drives that have shown read errors rarely improve.
  • Set up a regular backup so the next failure is an inconvenience rather than a crisis.

If the drive turned out to have mechanical symptoms, our comparison of recovery software vs a recovery service helps you decide on the next step.

Frequently asked questions

Why image a drive instead of scanning it directly?

Recovery scans can read a drive many times. Imaging reads it once, so a failing drive has less chance to get worse before you have a copy.

How much space does a drive image need?

Plan for at least the full size of the source drive, because the image is a sector-by-sector copy, including free space where deleted files live.

Can I image a drive that is not detected?

No. Imaging needs the drive to be visible to Windows. A drive that is not detected at all needs a professional lab.

Get three guides like this every month, plus software update notices.Subscribe →