The difference between a quick format and a full format in Windows is what happens to your data. A quick format writes a new, empty file system and leaves the old data on the drive, so it takes seconds and files can usually be recovered. A full format does the same, then checks every sector for errors and, in Windows Vista and later, writes zeros over the whole volume, so it takes much longer and the old data cannot be recovered with software. Use quick format for everyday reuse, and full format when you want to check a hard drive or wipe it before passing it on.
Below is what each one does, how long they take, and which to choose for your situation.
Quick format vs full format at a glance
| Quick format | Full format | |
|---|---|---|
| Writes a new file system | Yes | Yes |
| Checks for bad sectors | No | Yes |
| Writes zeros to every sector | No | Yes (Windows Vista and later) |
| Time on a 1 TB hard drive | Seconds | Hours |
| Old files recoverable with software | Usually, until overwritten | No |
| Good for | Reusing a drive you trust | Checking a hard drive, wiping before reuse or sale |
What a quick format does
A quick format creates a fresh file system on the volume: a new boot sector, a new empty file table (the MFT on NTFS, or the allocation table on FAT32 and exFAT) and an empty root folder. To Windows the drive now looks empty. But the areas that held your files are not touched. The old data sits there, marked as free space, until new files are saved over it.
This is why a quick-formatted drive is one of the most recoverable kinds of data loss. A recovery scan can often read the remains of the old file system, or find files by their content in a deep scan. See our guide to recovering data from a formatted hard drive for the full process.
What a full format does
A full format writes the new file system and then works through every sector of the volume. Since Windows Vista, it writes zeros to each sector as it goes and checks for sectors that cannot be read or written, marking any bad ones so they are not used. Once it completes, the previous contents of the volume are gone. Recovery software cannot get them back, because there is nothing left to find.
If a full format was stopped part way, only the part it reached was zeroed. The rest of the volume may still hold recoverable data.
Very old versions of Windows, such as Windows XP, did not zero the drive during a full format; they only scanned for bad sectors. The behavior described here applies to Windows Vista and every later version, including Windows 10 and 11.
How to choose quick or full format in Windows
In File Explorer
- Right-click the drive in File Explorer and choose Format.
- Choose the file system: NTFS for internal and external hard drives used only with Windows, exFAT for USB drives and SD cards shared with other devices, FAT32 only for small drives or devices that require it.
- Tick Quick Format for a quick format. Clear the tick for a full format.
- Click Start.
In Disk Management
Right-click the volume and choose Format. The Perform a quick format checkbox controls the type. When creating a new volume with New Simple Volume, the same option appears in the wizard.
From the command line
In an administrator Command Prompt, format E: /fs:ntfs /q performs a quick format. Leave out /q for a full format. Always double-check the drive letter before pressing Enter.
How long does a full format take?
A full format is limited by how fast the drive can write. As a rough guide, a hard drive writing at 100 to 200 MB/s takes somewhere between one and three hours per terabyte. USB flash drives and SD cards are often much slower, so a full format of a large, slow card can take hours. A quick format of any size usually completes in seconds.
SSDs are different
On an SSD, a quick format is usually enough even for wiping. When Windows formats an SSD that supports TRIM, it tells the drive that every block is now unused, and the SSD clears them internally. Data on a quick-formatted internal SSD is often unrecoverable soon after.
A full format on an SSD adds a full write of the whole drive, which is unnecessary wear and takes time without real benefit. For secure disposal of an SSD, use the drive maker's secure erase tool instead, which resets the flash memory properly. For more on SSD recovery, see recovering deleted files from an SSD.
Which one should you use?
- Reusing a USB drive or SD card you trust: quick format. For camera cards, format in the camera.
- Setting up a new external hard drive: quick format.
- A hard drive that has shown errors: full format will find and mark bad sectors, but recover your files first. A drive with errors is often failing, and a replacement is the safer choice.
- Selling or giving away a hard drive or USB drive: full format, so the old files cannot be recovered.
- Selling an SSD: the maker's secure erase tool, or Windows' Reset this PC with data cleaning turned on for a system drive.
- Windows says the drive "needs to be formatted": neither, until you have recovered your files. See you need to format the disk before you can use it.
Formatted the wrong drive?
If it was a quick format, stop using the drive immediately and do not save anything to it. Drive Restorer can read the old file system or run a deep scan by file signature to rebuild files from a quick-formatted hard drive, USB drive or SD card, and it never writes to the drive it is scanning. Preview what it finds, then restore everything to a different drive.
If it was a full format that ran to completion on a hard drive, USB drive or SD card, the data has been overwritten with zeros. Recovery software will not help, and your best option is a backup. If the full format was cancelled part way, scan the drive anyway: Drive Restorer can often find files in the part that was not reached.
Frequently asked questions
Can data be recovered after a quick format?
Usually, yes. A quick format writes a new file system but leaves the old data in place until it is overwritten.
Can data be recovered after a full format?
In Windows Vista and later, a full format writes zeros to every sector, so normal recovery software cannot get the data back.
Is a full format bad for an SSD?
It is unnecessary wear. A quick format on an SSD with TRIM already clears the data. Use the manufacturer's secure erase tool before disposal.
